Rozdíly

Zde můžete vidět rozdíly mezi vybranou verzí a aktuální verzí dané stránky.

--- networking:mikrotik [2018/12/12 14:33]
root vytvořeno
+++ networking:mikrotik [2020/04/15 15:32] (aktuální)
mwk [nahozeni LTE interface místo pppoe (30mbps limit):]
@@ Řádek 1: / Řádek 1: @@
-====== Mikrotik ======
+====== Mikrotik RouterOS ======
 ===== Topologie Mesh =====
@@ Řádek 47: / Řádek 47: @@
   * na klientovi nastavim jen L2TP dle secretu
   * pridam routu na interface tunelu
+===== EP06 v 9xx =====
+vypneme direct IP:
+<code>/port firmware
+set ignore-directip-modem=yes  </code>
+Reboot
+<code bash>
+/port
+set 0 name=usb1
+/interface ppp-client
+add apn=internet data-channel=3 dial-on-demand=no disabled=no info-channel=2 name=ppp-out1 port=usb1</code>
+**Nastaveni pro vdfcz, tmcz:**
+Data channel: 3
+Info channel: 2
+==== nahozeni LTE interface místo pppoe (30mbps limit): ====
+<code bash>/system routerboard usb set type=mini-PCIe</code>
+<WRAP center round important 60%>
+je treba prepnout USB na mpcie slot, misto klasickeho USB!
+</WRAP>
+<code bash>/port firmware set ignore-directip-modem=yes
+/system serial-terminal port=usb2 channel=2
+AT+QCFG="usbnet",1
+/port firmware set ignore-directip-modem=no
+/system reboot</code>
+pro navrat k pppoe:
+<code bash>AT+QCFG="usbnet",0
+USB integration modes na EC25:
+AT+QCFG="usbnet",0 - is PPP & QMI (default)
+AT+QCFG="usbnet",1 - is ECM.
+AT+QCFG="usbnet",2 - is MBIM</code>
+pro RSRP, SINR, nebo RSRQ:
+<code bash>AT+QENG="servingcell"
+</code>
+priklad uzamceni na band B28:
+<code bash>AT+QCFG=“band”,0,8000000,0,1</code>
+For any other bands hexadecimal value that specifies the LTE frequency bands, i.e. multiple bands can be selected by computing a logical OR of the individual value of each band (e.g.: 0x15 = 0x1(LTEB1)+0x4(LTE B3)+0x10(LTE B5)).
+If set to 0 or 0x40000000 LTE frequency bands are not changed.
+x7FFFFFFFFFFFFFFF means all available bands will be used
+x1 LTE B1
+x4 LTE B3
+x10 LTE B5
+x40 LTE B7
+x80 LTE B8
+x80000 LTE B20
+x7FFFFFFFFFFFFFFF Any frequency band (default setting)  - apparently this is not working with Mikrotik Routerboard, below is the new command that works
+All bands command that works with EC25 inside Mikrotiks:
+<code bash>at-chat lte1 input=“AT+QCFG=\“band\”,0,7777777,0,1”</code>
+HOW TO find the band the modem is currently on:
+<code bash>at-chat lte1 input=“AT+QNWINFO”</code>

Uživatelské nástroje

Nástroje pro tento web

Rozdíly

Nástroje pro stránku