Uživatelské nástroje
smarthome:carnet
Rozdíly
Zde můžete vidět rozdíly mezi vybranou verzí a aktuální verzí dané stránky.
| Následující verze | Předchozí verze | ||
|
smarthome:carnet [2019/02/20 19:17] mwk vytvořeno |
smarthome:carnet [2021/12/27 14:30] (aktuální) mwk |
||
|---|---|---|---|
| Řádek 1: | Řádek 1: | ||
| ====== Carnet ====== | ====== Carnet ====== | ||
| + | < | ||
| + | - napriklad na webu [[https:// | ||
| + | - vypalime na instalacni medium | ||
| + | - vlozime img do ciloveho stroje, kde je cilove medium | ||
| + | - cekame minimalne 20min | ||
| + | - rebootneme do nainstalovaneho systemu | ||
| + | |||
| + | ===== modem a ppp pres operatora ===== | ||
| + | <code bash>apt install wvdial</ | ||
| + | <code bash> | ||
| + | <file conf wvdial.conf> | ||
| + | [Dialer Defaults] | ||
| + | Modem = / | ||
| + | Modem Type = Analog Modem | ||
| + | ISDN*= 0 | ||
| + | Baud = 460800 | ||
| + | Dial Attempts = 1 | ||
| + | Username = o2 | ||
| + | Password = o2 | ||
| + | Init1 = ATZ | ||
| + | Init2 = AT&F &D2 &C1 | ||
| + | Init3 = ATS7=60 S30=0 S0=0 | ||
| + | Init4 = AT+CGDCONT=1," | ||
| + | Phone = *99# | ||
| + | Stupid Mode = 1 | ||
| + | </ | ||
| + | vyzkousime wvdial | ||
| + | |||
| + | pak do / | ||
| + | < | ||
| + | iface ppp0 inet wvdial</ | ||
| + | a reboot, default routa by mela jit pres ppp0</ | ||
| + | |||
| + | ===== LTE ===== | ||
| + | Uz nepouzivame vwdial, novejsi karty maji QMI. | ||
| + | Inicializace modemu a pripojeni | ||
| + | <code bash> | ||
| + | mmcli -m 0 --simple-connect=' | ||
| + | mmcli -m 0 --bearer=0 | ||
| + | </ | ||
| + | status overime | ||
| + | <code bash> | ||
| + | pokud je pripojeno, zjistime IP interfacu a pridame ji wwan0 | ||
| + | <code bash>ip link set wwan0 up | ||
| + | ip link set dev wwan0 mtu 1500 | ||
| + | ip link set dev wwan0 arp off | ||
| + | ip addr add XXX.XXX.XXX.XXX/ | ||
| + | ip route add default dev wwan0 metric 200 | ||
| + | </ | ||
| + | |||
| + | |||
| + | ===== tunel ===== | ||
| + | potrebujeme xl2tp: | ||
| + | upravit / | ||
| + | <file conf xl2tpd.conf> | ||
| + | [global] | ||
| + | access control = no | ||
| + | auth file = / | ||
| + | debug avp = no | ||
| + | debug network = no | ||
| + | debug packet = no | ||
| + | debug state = no | ||
| + | debug tunnel = no[lac “lns name you specified on the server”] | ||
| + | lns = “lns ip address (likely to be global address)” | ||
| + | redial = yes | ||
| + | redial timeout = 5 | ||
| + | require chap = yes | ||
| + | require authentication = yes | ||
| + | ppp debug = no | ||
| + | pppoptfile = / | ||
| + | require pap = no | ||
| + | autodial = yes | ||
| + | name = “username for chap authentication” | ||
| + | </ | ||
| + | * upravime / | ||
| + | * a nezapomeneme chmod 600 / | ||
| + | < | ||
| + | * udelame / | ||
| + | <file conf options.l2tpd> | ||
| + | ipcp-accept-local | ||
| + | ipcp-accept-remote | ||
| + | refuse-eap | ||
| + | require-mschap-v2 | ||
| + | noccp | ||
| + | noauth | ||
| + | idle 1800 | ||
| + | mtu 1410 | ||
| + | mru 1410 | ||
| + | defaultroute | ||
| + | usepeerdns | ||
| + | debug | ||
| + | lock | ||
| + | connect-delay 5000 | ||
| + | name " | ||
| + | password " | ||
| + | </ | ||
| + | a nezapomenem na routy dle potreby | ||
| + | |||
| + | ===== site ===== | ||
| + | sit zrzky 10.133.33.0/ | ||
| + | sit octy 10.133.35.0/ | ||
| + | sit karkulky 10.133.1.31.0/ | ||
smarthome/carnet.1550686629.txt.gz · Poslední úprava: 2019/02/20 19:17 autor: mwk
Nástroje pro stránku
Kromě míst, kde je explicitně uvedeno jinak, je obsah této wiki licencován pod následující licencí: CC Attribution-Share Alike 4.0 International
